Baileigh BSV-20VS-V2 Vertical Band Saw: Model Identification, Setup, and Common Repairs
You own a Baileigh BSV-20VS-V2 vertical band saw and you need to identify the model, set it up, or repair it. The Baileigh BSV-20VS-V2 is a variable speed vertical metal cutting band saw. You need to know the specifications, setup, and common repairs.
The Baileigh BSV-20VS-V2 is a variable speed vertical metal cutting band saw made by Baileigh Industrial. It is designed for contour cutting, notching, and general metal cutting in fabrication shops. The BSV-20VS-V2 has a 20-inch throat and variable speed control.
Model Identification
Baileigh BSV-20VS-V2
| Specification | Value |
|---|---|
| Model | BSV-20VS-V2 |
| Type | Vertical metal cutting band saw |
| Throat | 20 inches |
| Blade length | 150 inches (verify) |
| Blade width | 1/2 to 1 inch |
| Motor | 2 to 3 HP, 220V (verify) |
| Speed | Variable, 80 to 400 FPM (verify) |
| Coolant | Yes (built-in coolant system) |
| Table | ~20 x 20 inches (verify) |
| Table tilt | 0 to 45 degrees (verify) |
| Weight | ~800 to 1200 pounds (verify) |
How to Identify Your Model
- Find the model number on the label on the saw frame.
- If the label is missing, check for stamped numbers on the frame.
- Measure the blade length to help identify the model.
- Contact Baileigh customer service with any identifying numbers.
Setup
1. Position the Saw
- Place the saw on a level floor.
- Level the saw using the leveling feet.
- Bolt the saw to the floor if needed.
- Ensure adequate space around the saw for material handling.
2. Install the Blade
- Open the wheel covers.
- Release blade tension.
- Install the blade with teeth pointing down (toward the table).
- Apply tension according to the blade width.
- Check tracking.
- Close the wheel covers.
3. Adjust Blade Guides
- Set side guides to the correct clearance for the blade width.
- Set thrust bearing behind the blade.
- Check guide alignment.
4. Fill the Coolant System
- Mix coolant concentrate with water according to the manufacturer instructions.
- Fill the coolant tank.
- Check for leaks.
- Turn on the coolant pump and check the flow.
5. Set the Speed
- Set the blade speed based on the material:
- Mild steel: 80 to 200 FPM
- Stainless steel: 60 to 100 FPM
- Aluminum: 200 to 400 FPM
- Adjust the speed using the variable speed control.
6. Test Cut
- Clamp or hold a test piece on the table.
- Turn on the saw and coolant.
- Feed the test piece into the blade.
- Check that the cut is smooth and the saw is cutting properly.
Blade Selection
Blade Length
The BSV-20VS-V2 uses a 150-inch blade (verify).
Recommended TPI
| TPI | Best For | Material Thickness |
|---|---|---|
| 6 to 8 TPI | Thick solid bar | 1 to 4 inches |
| 10 TPI | General metal cutting | 1/4 to 2 inches |
| 14 TPI | Medium thickness | 1/8 to 1 inch |
| 18 TPI | Thin material | Under 1/4 inch |
| 10/14 variable pitch | Mixed thicknesses | All |
| 24 TPI | Very thin sheet metal | Under 1/8 inch |
Blade Material
Bi-metal M42: Standard for general metal cutting. Bi-metal M51: For tough materials like stainless steel. Carbide-tipped: For production cutting.
Common Repairs
1. Blade Replacement
When: Cuts become rough or blade breaks. Cost: 30 to 80 dollars.
2. Coolant Pump Repair
When: Coolant pump does not work or flow is low. Cost: 50 to 150 dollars.
3. Drive Belt Replacement
When: Belt is cracked, stretched, or slipping. Cost: 15 to 30 dollars.
4. Blade Guide Replacement
When: Guides are worn and blade wanders. Cost: 30 to 80 dollars.
5. Motor Repair
When: Motor does not run or makes excessive noise. Cost: 200 to 500 dollars.
6. Variable Speed Control Repair
When: Speed control does not work or is erratic. Cost: 100 to 300 dollars.
7. Table Tilt Mechanism Repair
When: Table does not tilt or is stiff. Cost: 50 to 150 dollars.
Maintenance
Daily: Clean chips from the table and blade area. Check the blade. Check the coolant level. Weekly: Clean the blade guides. Check the coolant concentration. Check the drive belt. Monthly: Check all bolts and fasteners. Lubricate the table tilt mechanism. Annually: Check the motor. Inspect the coolant pump. Replace the drive belt if worn. Check the blade guides.
FAQ
What blade does the Baileigh BSV-20VS-V2 use?
A 150-inch blade (verify) in widths from 1/2 to 1 inch. Use bi-metal M42 for general metal cutting. Check the manual to confirm the blade length.
Can I cut stainless steel with the Baileigh BSV-20VS-V2?
Yes, with a bi-metal M42 or M51 blade at 60 to 100 FPM. Use a slower speed and lighter feed pressure. Use coolant to prevent work hardening.
Where can I find parts for my Baileigh BSV-20VS-V2?
Baileigh customer service, industrial supply companies (MSC, Grainger, McMaster-Carr), Amazon, and eBay. Blades are widely available. Model-specific parts are available from Baileigh.
References
- Baileigh Industrial. “BSV-20VS-V2 Owner’s Manual.” baileigh.com.
- LENOX Tools. “Metal Cutting Blade Guide.” LENOX Industrial Division.
- Starrett. “Bi-Metal Blade Specifications.” L.S. Starrett Company.
- Practical Machinist. “Vertical Band Saw Guide.” practicalmachinist.com.
- Modern Machine Shop. “Band Saw Cutting Speeds and Feeds.” Gardner Business Media.
