Craftsman 9-Inch Band Saw: Model Identification, Setup, and Common Repairs
You own a Craftsman 9-inch band saw and you need to identify the model, set it up, or repair it. The Craftsman 9-inch band saw is a compact benchtop band saw sold by Sears under the Craftsman brand. You need to know the models, specifications, and common repairs.
The Craftsman 9-inch band saw is a compact benchtop band saw sold by Sears under the Craftsman brand. It was manufactured by Emerson Electric and later by TTI. The 9-inch saw is designed for hobby use and light shop work.
Model Identification
Common Craftsman 9-Inch Models
| Model Series | Manufacturer | Blade Length | Motor | Notes |
|---|---|---|---|---|
| 113.24xxxx | Emerson Electric | 59-1/2 inches | 1/3 HP | Common |
| 113.298xxx | Emerson Electric | 59-1/2 inches | 1/3 HP | Similar |
| BAS230 | TTI | 59-1/2 inches | 1/3 HP | Newer model |
| 21400 | TTI | 59-1/2 inches (verify) | 1/3 HP | Newer model |
How to Identify Your Model
- Find the model number on the label on the saw frame.
- If the label is missing, look for a stamped number on the frame.
- Measure the blade length. A 59-1/2 inch blade indicates a 9-inch Craftsman saw.
- Check the motor label for horsepower and voltage.
- Look up the model number on Sears Parts Direct or eReplacementParts.
Specifications
| Specification | Value |
|---|---|
| Type | 9-inch benchtop band saw |
| Throat | 8 to 9 inches |
| Resaw capacity | 3-1/2 inches |
| Blade length | 59-1/2 inches |
| Blade width | 1/8 to 3/8 inch |
| Motor | 1/3 HP, 120V |
| Speed | ~2500 FPM (single speed) |
| Table | ~11 x 11 inches |
| Table tilt | 0 to 45 degrees |
| Weight | ~35 to 45 pounds |
Setup
1. Unbox and Inspect
- Remove all packaging material.
- Check for shipping damage.
- Verify all parts are included: saw, fence, miter gauge, blade, manual.
2. Mount the Saw
- Place the saw on a sturdy workbench.
- Secure the saw with bolts or clamps.
- Check that the table is level.
3. Install the Blade
- Open the wheel covers.
- Release blade tension.
- Install the blade with teeth pointing down (toward the table).
- Apply tension.
- Check tracking.
- Close the wheel covers.
4. Adjust Blade Guides
- Set side guides about 1/32 inch from the blade.
- Set thrust bearing about 1/64 inch behind the blade.
- Set guide post height about 1/4 inch above the workpiece.
5. Adjust the Fence
- Set the fence to the desired width.
- Check that the fence is parallel to the blade.
- Lock the fence.
6. Test Cut
- Turn on the saw.
- Feed a test piece into the blade.
- Check that the cut is straight and the saw is stable.
Blade Selection
The Craftsman 9-inch band saw uses a 59-1/2 inch blade.
Recommended Blades
| Application | Width | TPI | Material | Cost |
|---|---|---|---|---|
| General woodworking | 1/4 inch | 6 TPI | Carbon steel | 10 to 15 dollars |
| Curve cutting | 1/8 inch | 14 TPI | Carbon steel | 10 to 12 dollars |
| Ripping | 3/8 inch | 4 TPI | Carbon steel | 12 to 18 dollars |
Cross-Brand Compatibility
The 59-1/2 inch blade is shared with Delta 9-inch, Ryobi 9-inch, WEN 9-inch, Skil 9-inch, and Central Machinery 9-inch saws.
Common Repairs
1. Blade Replacement
When: Cuts become rough or blade breaks. Cost: 10 to 15 dollars.
2. Tire Replacement
When: Tires are cracked, hardened, or causing tracking problems. Replacement: Urethane tires for 9-inch wheels. Cost: 15 to 25 dollars per pair.
3. Blade Guide Upgrade
When: Guides are worn or you want better cut quality. Upgrade: Cool Blocks from Olson Saw. Cost: 15 to 20 dollars.
4. Drive Belt Replacement
When: Belt is cracked, stretched, or slipping. Cost: 8 to 15 dollars.
5. Wheel Bearing Replacement
When: Saw makes grinding or rumbling noise. Cost: 15 to 25 dollars per bearing.
6. Switch Replacement
When: Switch does not work reliably. Cost: 10 to 15 dollars.
7. Motor Replacement
When: Motor does not run, smokes, or makes excessive noise. Cost: 60 to 120 dollars.
Maintenance
Daily: Clean sawdust from table and wheels. Check blade. Weekly: Clean wheel covers. Lubricate guide post. Monthly: Check drive belt tension. Check bolts. Annually: Replace tires if worn. Check bearings. Inspect cord and switch.
FAQ
What blade does the Craftsman 9-inch band saw use?
A 59-1/2 inch blade in widths from 1/8 to 3/8 inch. Carbon steel blades cost 10 to 15 dollars.
Can I resaw with a Craftsman 9-inch band saw?
Yes, but with limited capacity. The resaw capacity is 3-1/2 inches. Use a 3/8 inch, 4 TPI skip tooth blade for resawing.
Where can I find parts for my Craftsman 9-inch band saw?
Sears Parts Direct, eReplacementParts, Amazon, and eBay. Blades and tires are widely available. Model-specific parts may be harder to find for older models.
References
- Sears Parts Direct. “Craftsman 9-Inch Band Saw Parts.” searspartsdirect.com.
- eReplacementParts. “Craftsman 113.24xxx Parts Diagram.” eReplacementParts.com.
- Olson Saw. “59-1/2 Inch Band Saw Blade Guide.” Olson Saw Company.
- Fine Woodworking. “Benchtop Band Saw Setup.” Taunton Press.
- Vintage Machinery. “Craftsman 9-Inch Band Saw Reference.” vintagemachinery.org.
