Craftsman 14-Inch Band Saw: Model Identification, Setup, and Common Repairs

You own a Craftsman 14-inch band saw and you need help with model identification, setup, or repairs. The Craftsman 14-inch band saw is a floor-standing woodworking saw that has been sold under several model numbers over the years. You need to know the specifications, how to set it up, and how to fix common problems.

The Craftsman 14-inch band saw is a floor-standing woodworking saw designed for serious hobby and light professional use. It has been manufactured by different companies over the years, including Emerson Electric and TTI. The saw uses a 93-1/2 inch blade and has a 6-inch resaw capacity (12 inches with a riser block).

Model Identification

Common Models

Model	Manufacturer	Blade Length	Motor	Notes
113.298031	Emerson Electric	93-1/2 inches	3/4 HP	Common older model
113.298030	Emerson Electric	93-1/2 inches	3/4 HP	Similar to above
113.298240	Emerson Electric	93-1/2 inches	3/4 HP	Variant
22400	TTI	93-1/2 inches	3/4 to 1 HP	Newer model
BAS350	Various	93-1/2 inches	3/4 HP	Budget model
21400	Various	93-1/2 inches	3/4 HP	Another variant

How to Identify Your Model

1. Find the model number on the label on the saw frame or column.
2. If the label is missing, measure the blade length. A 93-1/2 inch blade indicates a 14-inch saw.
3. Check the motor label for horsepower and voltage.
4. Look up the model number on Sears Parts Direct or eReplacementParts.

Specifications

Specification	Value
Type	14-inch floor-standing woodworking band saw
Throat	13-1/2 to 14 inches
Cut capacity	6 inches (12 inches with riser block)
Blade length	93-1/2 inches (105 inches with riser)
Blade width	1/8 to 3/4 inch
Motor	3/4 to 1 HP, 120V
Speed	Single or two speed, 2500 to 3000 FPM
Table	Cast iron, 15 x 15 inches
Table tilt	0 to 45 degrees
Weight	200 to 250 pounds

Setup

1. Install the Blade

1. Open the wheel covers.
2. Release blade tension.
3. Install the blade with teeth pointing down (toward the table).
4. Apply tension to the recommended setting.
5. Check tracking.
6. Close the wheel covers.

2. Adjust Blade Guides

Upper guides:

1. Set the side guides about 1/32 inch from the blade sides.
2. Set the thrust bearing about 1/64 inch behind the blade.
3. Set the guide post height about 1/4 inch above the workpiece.

Lower guides: Same procedure as upper guides.

3. Align the Table

1. Check that the table is 90 degrees to the blade.
2. Adjust the trunnion bolts if needed.
3. Check the table for flatness.

4. Set Up the Fence

1. Install the fence on the table.
2. Check that the fence is parallel to the blade.
3. Adjust the fence alignment if needed.

Blade Selection

The Craftsman 14-inch band saw uses a 93-1/2 inch blade (105 inches with a riser block).

Recommended Blades

General woodworking: 3/8 inch, 4 TPI skip tooth, carbon steel. Cost: about 15 dollars. Resawing: 1/2 inch, 3 TPI hook tooth, bi-metal M42. Cost: about 25 dollars. Curve cutting: 1/4 inch, 6 TPI skip tooth, carbon steel. Cost: about 15 dollars. Scroll work: 1/8 inch, 14 TPI, carbon steel. Cost: about 12 dollars.

Cross-Brand Compatibility

The 93-1/2 inch blade is shared with:

• Delta 14-inch saws (28-276, 28-400, 28-195)
• Jet 14-inch saws (JWBS-14, JWBS-14OS)
• Grizzly 14-inch saws (G0555, G0555P)
• Rikon 14-inch saws (10-305, 10-321)
• Most other 14-inch saws

Blades from Olson Saw, Timber Wolf, and other manufacturers will fit the Craftsman 14-inch saw.

Common Repairs

Replacing Tires

Tires harden and crack after 5 to 10 years. Replacement: Urethane tires for 14-inch wheels. Soak in hot water before installation. Cost: 20 to 35 dollars per pair.

Upgrading Blade Guides

Cool Blocks: 15 to 20 dollars. Replace stock metal guide blocks. Carter bearing guides: 50 to 80 dollars. Replace the entire guide assembly.

Replacing Wheel Bearings

Cost: 15 to 30 dollars per bearing. Read the bearing number on the old bearing.

Replacing the Drive Belt

Cost: 10 to 20 dollars. Measure the old belt.

Motor Repair

• Start capacitor: 10 to 20 dollars (if applicable)
• Motor replacement: 80 to 200 dollars

Switch Replacement

Cost: 10 to 20 dollars.

Replacing the Tension Spring

If the blade tension will not hold, the tension spring may be weak or broken. Cost: 15 to 25 dollars.

Restoration Tips

Clean everything. Disassemble the saw, clean all parts, and remove old grease and sawdust.

Replace the tires. New urethane tires make a big difference in blade tracking and cut quality.

Install a good blade. A quality blade from Olson Saw or Timber Wolf makes more difference than any other single change.

Align the table. Check that the table is 90 degrees to the blade. Shim the trunnion if needed.

Upgrade blade guides. Cool Blocks or Carter bearing guides improve cut quality.

Add a quick-release tensioner. Makes blade changes easier and extends blade life by releasing tension when not cutting.

Add dust collection. Connect a dust collector to the 4-inch port.

Upgrades

1. Install a quality blade. The single most important upgrade.
2. Upgrade to urethane tires. Better tracking and longer life.
3. Add a riser block. Increases resaw capacity from 6 to 12 inches.
4. Upgrade blade guides. Cool Blocks or Carter bearing guides.
5. Add a quick-release tensioner. Easier blade changes and longer blade life.
6. Add dust collection. Connect a dust collector to the 4-inch port.
7. Install a mobile base. Makes the saw easier to move.

FAQ

What blade does the Craftsman 14-inch band saw use?

A 93-1/2 inch blade in widths from 1/8 to 3/4 inch. With a riser block, the blade length is 105 inches. Carbon steel for general work, bi-metal for resawing.

Can I resaw with a Craftsman 14-inch band saw?

Yes, with a 1/2 inch, 3 TPI hook tooth bi-metal blade. The resaw capacity is 6 inches without a riser block and 12 inches with a riser block.

Where can I find parts for my Craftsman 14-inch band saw?

Sears Parts Direct, eReplacementParts, aftermarket suppliers like Olson Saw and Carter Products, and eBay for discontinued parts.

Are Craftsman 14-inch band saw blades interchangeable with Delta and Jet?

Yes. The 93-1/2 inch blade is shared with most 14-inch band saws, including Delta, Jet, Grizzly, and Rikon. Blades from any manufacturer will fit.

References

• Sears Parts Direct. “Craftsman 14-Inch Band Saw Owner’s Manuals.” searspartsdirect.com.
• eReplacementParts. “Craftsman Band Saw Parts.” eReplacementParts.com.
• Olson Saw. “93-1/2 Inch Band Saw Blade Guide.” Olson Saw Company.
• Carter Products. “Guide Upgrade Compatibility Chart.” Carter Products.
• Fine Woodworking. “14-Inch Band Saw Setup.” Taunton Press.