Milwaukee Band Saw Table: How It Works and Where It Fits

You own a Milwaukee portable band saw and you want to add a table for stationary use. A Milwaukee band saw table is an accessory that mounts to the saw and provides a flat surface for supporting material during cutting. You need to know what it does, which models it fits, and how to set it up.

A Milwaukee band saw table is an accessory that attaches to a Milwaukee portable band saw and provides a flat work surface. The material rests on the table while the blade cuts through it, similar to a stationary band saw. This allows you to use both hands to guide the material for more accurate cuts.

Types of Milwaukee Band Saw Tables

Milwaukee 48-08-0260 Table Stand

A stand and table combination designed for Milwaukee deep cut and compact band saws.

Compatibility: Fits Milwaukee 2729-20, 2929-20, 6232-20, 2429-20, and other Milwaukee portable saws. Features: Material table, fence, quick-release saw mounting. Cost: 80 to 120 dollars.

Milwaukee 48-08-0261 Table

A table-only accessory that attaches to the saw without a stand.

Compatibility: Fits specific Milwaukee models. Check compatibility. Features: Table surface, fence guide. Cost: 40 to 70 dollars.

Aftermarket Tables

Tables made by third-party manufacturers.

Compatibility: Varies. Check compatibility with your saw model. Features: Varies by manufacturer. Cost: 30 to 80 dollars.

How It Works

1. Mount the table to the saw according to the manufacturer instructions.
2. Install the blade and apply tension.
3. Adjust the fence for straight cuts.
4. Place the material on the table.
5. Start the saw and feed the material into the blade.
6. Guide the material along the fence for straight cuts, or freehand for curves.

Compatible Milwaukee Saws

Model	Type	Table Compatibility
2729-20	M18 FUEL deep cut	Yes (48-08-0260)
2929-20	M18 FUEL deep cut (newer)	Yes (48-08-0260)
6232-20	Corded deep cut	Yes (48-08-0260)
2429-20	M18 compact	Yes (check compatibility)
2629-20	M18 FUEL compact	Yes (check compatibility)
6238-20	Corded deep cut (variable speed)	Yes (48-08-0260)

Setup

1. Mount the Table

1. Remove the battery (if cordless) or unplug (if corded).
2. Position the table on the saw according to the instructions.
3. Clamp or bolt the table to the saw.
4. Check that the table is secure and level.

2. Install the Blade

1. Install the correct blade for your material.
2. Apply tension.
3. Check tracking.

3. Adjust the Fence

1. Set the fence to the desired width.
2. Check that the fence is parallel to the blade.
3. Lock the fence in position.

4. Test Cut

1. Install the battery or plug in.
2. Turn on the saw and let it reach full speed.
3. Feed a test piece into the blade.
4. Check that the cut is straight and the table is stable.

Uses

Straight Cuts

Use the fence to guide the material for straight cuts. The fence provides a reference edge for repeatable cuts.

Angle Cuts

Some tables have an adjustable angle guide for miter cuts. Set the angle and feed the material along the guide.

Curve Cuts

Remove the fence and guide the material freehand for curve cuts. The table provides support while you rotate the material.

Repeatable Cuts

The fence and table setup allow repeatable cuts of the same length and angle.

Advantages

1. Both hands free: You can use both hands to guide the material.
2. More accurate cuts: The table and fence provide reference surfaces.
3. Less fatigue: You do not have to hold the saw.
4. Repeatable cuts: The fence allows repeatable cuts.
5. Portable: The table is compact and portable, unlike a stationary saw.

Limitations

1. Limited capacity: Portable saws have less cut capacity than stationary saws.
2. Single speed: Most Milwaukee portable saws have a single speed.
3. No coolant: Portable saws do not have coolant systems.
4. Table size: The table is smaller than a stationary saw table.
5. Not as rigid: The setup is not as rigid as a dedicated stationary saw.

FAQ

What is a Milwaukee band saw table?

An accessory that attaches to a Milwaukee portable band saw and provides a flat work surface for supporting material during cutting, similar to a stationary band saw.

Which Milwaukee band saws are compatible with the table?

The 48-08-0260 table stand fits Milwaukee 2729-20, 2929-20, 6232-20, 6238-20, and other deep cut models. Check compatibility for compact models like 2429-20 and 2629-20.

Can I cut curves with a Milwaukee band saw table?

Yes. Remove the fence and guide the material freehand for curve cuts. The table provides support while you rotate the material.

How much does a Milwaukee band saw table cost?

40 to 120 dollars depending on the model. The 48-08-0260 table stand costs 80 to 120 dollars. Table-only accessories cost 40 to 70 dollars.

References

• Milwaukee Tool. “48-08-0260 Portable Band Saw Table Stand Guide.” Milwaukee Tool.
• Milwaukee Tool. “Portable Band Saw Accessories Catalog.” Milwaukee Tool.
• Pro Tool Reviews. “Milwaukee Band Saw Table Review.” ProToolReviews.com.
• Tool Box Buzz. “Milwaukee Portable Band Saw Accessories.” ToolBoxBuzz.com.